Explosion Proof Parallel Shaft Helical Hoisting and Conveying Gearbox
Lifting and bulk handling equipment installed inside a classified hazardous area faces two unrelated sets of rules at once. Mechanical rules come from the load spectrum — reversing hoist cycles, braking, jammed buckets, shock on engagement. Compliance rules come from the atmosphere itself, where any hot surface or metallic spark becomes an ignition source.
The MPAF159-YBVP22-4P-270º-96.53-M4 gearbox was engineered for installations where both rule sets apply simultaneously. The unit pairs a three-stage parallel shaft helical gear reducer in a size 159 cast iron housing with a 22 kW four-pole explosion proof inverter-duty motor, flange mounted to B5 and configured with a hollow output shaft at an angular orientation of 270° in the M4 mounting position.
Core Technical Specifications
| Parameter | Value |
|---|---|
| Gearbox Model | MPAF159-YBVP22-4P-270º-96.53-M4 Custom Build |
| Gearbox Type | Parallel shaft helical gear unit (MP series) |
| Frame Size | 159 |
| Gear Stages | Three-stage helical gear reduction |
| Mounting Style | B5 flange mounted, hollow output shaft AF |
| Mounting Position | M4 |
| Output Flange Orientation | 270° |
| Nominal Ratio | 96.53 : 1 |
| Motor Rating | 22 kW, 4-pole, 1,460 rpm nominal |
| Motor Type | Explosion proof, inverter (VFD) duty, forced ventilation |
| Output Speed | ≈ 15.1 rpm at 50 Hz |
| Output Torque | ≈ 13,900 Nm at rated input |
| Housing Rated Torque (size 159) | ≈ 18,000 Nm, giving a service factor near 1.3 |
| Permissible Radial Load | ≈ 55 kN at hollow shaft mid-length |
| Gear Material | Case-hardened, ground helical gearing, 20CrMnTi |
| Housing Material | HT250 cast iron, ribbed for heat dissipation |
| Enclosure Rating | IP65 standard, IP66 on request |
| Application Field | Hoisting, long-travel and bulk conveying in classified areas |
The Engineering Challenge in a Classified Lifting Area
Coal yards, grain terminals, LNG jetties and petrochemical loading bays all move material with hoists, gantries and belt conveyors. Every one of the listed sites carries a Zone 1, Zone 21 or Zone 22 classification over at least part of the travel path. Equipment operating inside the zones must not become an ignition source under normal operation or under a foreseeable fault.
A gear unit contributes risk in three ways. Gear mesh and bearing friction raise housing surface temperature. A seizing bearing or a dry gear mesh raises surface temperature far beyond the design figure. A ruptured seal leaks hot oil onto hot surfaces and onto accumulated combustible dust.
Mechanical duty compounds the compliance problem. A hoist gearbox engages, brakes and reverses full load thousands of times per shift, while a travel gearbox absorbs wheel skew and rail irregularity. Steady-state power ratings written for a pump application have no meaning under a load spectrum of the kind described.
Why the MPAF159 Configuration Fits
Reduction of 96.53:1 across three helical stages brings the 1,460 rpm motor shaft down to roughly 15.1 rpm at the hollow output shaft. Output torque reaches approximately 13,900 Nm at rated input power. Frame size 159 carries a nominal rating near 18,000 Nm, leaving a service factor of about 1.3 — the band AGMA Class II to Class III duty and FEM crane classification both call for under moderate shock with reversing operation.
Three-stage reduction keeps individual gear mesh loads modest in comparison with a two-stage unit forced to the same ratio. Lower mesh loading reduces friction losses, and lower friction losses reduce housing surface temperature — a direct contribution to compliance margin rather than a marketing point.
Helical gearing is ground after case hardening to profile accuracy grade 6 per GB/T 10095. Accurate flank geometry distributes load across the full face width, so peak contact stress during a braking event stays inside the material limit. Reversing duty punishes inaccurate gearing faster than any other load pattern.
Ignition Risk and the Certified Motor-Gearbox Package
The gear unit and the motor are supplied as one compliant package rather than two separately procured items. The 22 kW four-pole motor is built to explosion proof construction for gas and dust atmospheres, with a temperature class suited to Zone 1 and Zone 21 installations and a terminal enclosure rated IP65 as standard.
The cast iron gearbox housing is machined on all mating faces and sealed with oil-resistant gaskets, so no oil mist escapes into the surrounding atmosphere. External surfaces carry no light alloy content capable of a friction spark against rusted steel. Breather placement and oil level are selected for the M4 mounting position so the gear train stays submerged without pressurising the seal lips.
Surface temperature is limited by design rather than by assumption. Thermal power rating for the size 159 housing is calculated at the specified ambient and duty cycle, and the motor carries its own forced ventilation unit. Independent cooling matters because a shaft-mounted fan loses most of its airflow below 25 Hz, exactly where a creep-speed positioning cycle operates.
Shock Loading, Reversing Duty and Overhung Load
Hoisting load never arrives smoothly. Slack rope take-up, load release and emergency braking each impose a torque spike well above the steady figure, and a jammed grab imposes stall torque limited only by motor breakdown torque.
Bearings at the output stage are sized on the crane load spectrum, not on nominal power. The hollow output shaft accepts a radial load of approximately 55 kN applied at mid-length, which covers sprocket and pulley arrangements on travel axles and head pulleys alike. Output bearing spacing is widened in the size 159 housing to reduce shaft deflection under the same load.
For hoisting applications with a credible jam condition, TANHON supplies the unit with a torque limiter or a hydraulic coupling at the motor adapter. Either component caps the torque reaching the gear train at a preset multiple of rated value, protecting gearing and structure during the fault.
Inverter Duty Operation
Inverter control is standard practice on modern hoisting and conveying equipment, and the YBVP motor designation reflects dedicated inverter-duty construction — reinforced insulation, independent cooling and a shaft earthing arrangement against bearing currents. Speed range from 5 Hz to 50 Hz gives an output band of roughly 1.5 to 15.1 rpm at the hollow shaft.
Extended operation at low frequency is the point where many gear units fail thermally. Oil viscosity rises, churning losses persist, and the motor fan no longer moves air. Forced ventilation on the motor plus the enlarged, ribbed housing of frame 159 keep the thermal power rating above the demanded mechanical power across the full speed band.
Sealing, Lubrication and Service Access
A hazardous-zone installation is often the hardest place in the plant to reach. Scaffolding, gas detection and hot-work permits turn a ten-minute oil top-up into a half-day exercise, so field service intervals must be long by design.
Output shafts carry a double lip seal arrangement with a dynamic drain-back groove, returning oil to the sump instead of pushing it past the lip. Labyrinth protection ahead of the seal keeps coal dust and grain dust out of the sealing zone. Dust ingress, not seal wear, causes most leakage reports in bulk handling plants.
Oil fill for the M4 position at size 159 is approximately 19 litres of mineral gear oil, ISO VG 220 at normal ambient temperature, with synthetic PAO available for lifetime lubrication. Fill, drain and level points are positioned for M4 at the factory, so no plug relocation occurs on site.
Mounting and Interchangeability
The AF designation combines a B5 flange face with a hollow output shaft, bolting the gearbox directly onto the machine frame and eliminating the separate bedplate and shaft coupling. Fewer alignment interfaces means fewer sources of overhung load error on the output bearings.
The hollow bore accepts either a keyed hub or a shrink disc connection. Shrink disc mounting is the preferred choice for reversing hoist duty because backlash-free clamping removes the fretting wear keyways develop under thousands of torque reversals.
Dimensionally the MP series follows the parallel shaft helical convention familiar from SEW F157 and Flender H-series units, so a replacement fits existing foundations and shaft arrangements without structural rework. Full dimensional verification against existing equipment is carried out before production release.
Manufacturing Background
TANHON — Zhejiang Tianhong Transmission Machinery Co., Ltd. — has built gear units in Ruian City, Zhejiang Province since 1989, with a monthly capacity of 80,000 units across more than 30 series covering 0.18 kW to 4,000 kW. The company holds 98 independent patents, comprising 4 invention patents, 62 utility model patents and 32 design patents.
Production operates under ISO 9001 and ISO 14001, with CE and EAC conformity for the European and Eurasian markets. Every hazardous-area unit is supplied with motor certification documentation, calculated thermal power rating and the service factor used in selection, so the compliance file for the complete package is closed before shipment.
